Hewlett Packard RESET METHOD

To clear the Maintenance Service Message from the LCD display:

HP IIISi Printers:

1. Press
ONLINE until the light goes off
2. Hold down
MENU until PCL CONFIG MENU appears
3. Press the
MENU key until SERVICE MSG=ON* appears
4. Press the
+ or - key to change display to SERVICE MSG=OFF
5. Press
ENTER/RESET MENU key to turn message off, the * should appear, then press ONLINE

HP 4Si Printers:

1. Press
ONLINE until the light goes off
2. Press
MENU until CONFIG MENU appears
3. Press the
ITEM key until SERVICE MSG=ON* appears
4. Press the
+ or - key to change display to SERVICE MSG=OFF
5. Press the
ENTER key to turn message off, the * should appear, then press ONLINE

HP 5Si:

1. Press
MENU key 4 times for CONFIG MENU
2. Press
ITEM to display SERVICE MESSAGE=OFF
3. Press
ENTER
4. Press
ONLINE

HP 4000/4050/4100/5000 Printers:

1. Turn the printer off
2. Hold down the left side of the
ITEM and VALUE +/- keys, turn the printer on and wait
until RESET MAINTENANCE COUNT is displayed and then release the keys

HP 4500/4550 Printers:

1. Turn the printer off
2. Hold down the
CANCEL JOB and SELECT keys and turn the printer on, then wait until the display goes blank and the three LED's come on
3. Press the right side of the
MENU key, then press the SELECT key
4. You will enter
SERVICE MODE after the normal test completes
5. Press the
ITEM key until the FUSER MAINTENANCE COUNT appears
6. Press
VALUE +/- to change to zero
7. Press
SELECT to save
8. Press
GO; the printer should return to READY

HP 8000/8100/8150 Printers:

1. Press the
MENU button until the display reads CONFIGURATION MENU
2. Press the
ITEM button until the display reads SERVICE MESSAGE = ON/OFF
3. Select
OFF*
4. Press
SELECT to save
5. Turn printer off
6. Hold the
VALUE MINUS and ITEM MINUS buttons while turning the printer back on Hold buttons down until display reads RESET MAINT/COUNTand then release both buttons

HP 9000 Printers:

1. Turn the printer off
2. Press and hold the
CHECK key
3. Power on the printer
4. Release the
CHECK key after all three lights come on The display should read SELECT LANGUAGE
5. Press the up arrow until
MAINTENANCE KIT is displayed, then press the CHECK key again and the maintenance kit count has been reset

HP Color LaserJet 4500/4550 Printers (TRANSFER KIT RESET):

1. Press the
MENU button until the RESETS MENU is displayed
2. Press the
ITEM button until TRANSFER KIT SELECT IF DONE is displayed
3. Press the
SELECT button

HP Color LaserJet 4500/4550 Printers (FUSER KIT RESET):

1. Press the
MENU button until the RESETS MENU is displayed
2. Press the
ITEM buton until FUSER KIT SELECT IF DONE is displayed
3. Press the
SELECT button
4. Press the
GO button to return to READY

HP Color LaserJet 4600 Printer (IMAGE TRANSFER KIT (ETB) RESET):

1. After Maintenance is performed, the display should read
NEW TRANSFER KIT =
2. Press the down arrow to highlight
YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW TRANSFER KIT and select

HP Color LaserJet 4600 Printer (FUSER KIT RESET):

1. After Maintenance is performed, the display should read
NEW FUSER KIT =
2. Press the down arrow to highlight
YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW FUSER KIT and select

HP Color LaserJet 8500/8550 Printers (TRANSFER KIT RESET):

1. Press the
MENU button until the RESETS MENU is displayed
2. Press the
ITEM button until RESET TRANSFER LIFE COUNT is displayed
3. Press the
SELECT button to reset, then GO to return to READY

HP Color LaserJet 8500/8550 Printers (FUSER KIT RESET):

Press the

MENU button until the RESETS MENU is displayed

Press the

ITEM buton until RESET FUSER LIFE COUNT is displayed

Press the

SELECT button to reset

CANON RESETTER 2

CANON Ink Tank Full - PART II

Canon Waste Ink Tank Reset Procedures

I found it from some website and I want everybody know it too. How to repair your printer when that say "Waste Ink Absorber Full" or "Ink Tank Full", see at below how to resolve the problem.

Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button.
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
succession. Note: you are still holding the POWER button). The printer's carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the
"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

====================================================================================

Canon i320, i255
Waste Ink Counter Reset.
Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (L.E.D.) should be green.
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.
6. Release both buttons.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

====================================================================================

Canon PIXMA iP1000
Waste Ink Counter Reset.
Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

====================================================================================

Canon PIXMA iP1200, 1300, 1500, 1600, 1700, 1800
Waste Ink Counter Reset.
Step 1: Manual for Service mode
Start with the printer OFF
1. Unplug power and USB.
2. Hold down POWER and plugin the cable power
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done blinking

step 2 : Software for Permanant

1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.

Remark "After service mode Pls use software for permanent reset"

====================================================================================

Canon i850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

====================================================================================

Canon S450 Printer
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
7: Press Power to set data

====================================================================================

Canon S200SPx

1. Without the cartridge installed and with the front cover closed, connect the AC cord
while holding down the RESET button.

2. Release the RESET button, press it down again within less than 5 sec and before the
cartridge carrier starts to move and make a sound (this is critical timing, if you hear the
printer, you are too late. Start again - they don't tell you this in tha manual, it is a
given)

3. Hold down the RESET button for 2 sec or more and realease it once again.

4. EEPROM reset - Quickly again and before the printer satrts to move and make more sounds,
hold down the RESET button for 2 secs or more and release it.

====================================================================================

Canon BJC 1000 Series
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

====================================================================================

Canon BJC-2000 BJC-2100 Serie
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

====================================================================================

Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
1. Unplug Power Cord
2. Hold POWER and RESUME buttons
3. Plug in Power Cord
4. Release buttons
5 .Open front door of printer
6. Hold the CARTRIDGE and RESUME buttons
7. Press POWER
8. Release all buttons after the beeps
9. Press CARTRIDGE once
10. Press RESUME

====================================================================================

Canon BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

====================================================================================

Canon BJC-5100
Self Test
Switch Printer off. Hold Power for 1 beep.

Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , Press and hold RESUME until the printer plays a melody of beeps.

CANON RESETTER

CANON Ink Tank Full - PART I

Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data

====================================================================================

Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps

====================================================================================

Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord

====================================================================================

Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer

====================================================================================

Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.

====================================================================================

Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above.
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

====================================================================================

Canon S900, S820, S750, S520

1. Turn off the printer.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
4. The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.
5. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
   
   1. Service/factory test printout, including ink sensor check
   2. EEPROM info printout
   3. EEPROM initialization
   4. Clear the waste-ink counter
   5. Printer model setting. (more selections beyond this- leave this alone)
   
6. After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.

===================================================================

Canon S9000

1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

===================================================================

Canon MPC190
Reset Waste Ink
1) Enter SERVICE MODE.
By pressing Menu, Copy, Scan, Copy, Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.

====================================================================================

Canon MP160 , MP145
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)

Error Code :
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error
====================================================================================

Canon MP390
1)Printer on, press Additional Functions, Scan, Copy, Scan
Now you should be in service mode from there for waste ink tank reset it is simalar to what has already been posted

2)Select Test mode which is like the last avalabe selection
3)Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button

The menu will now say EEPRON Clear
Select Ink count which is option (0) and press set

Then press Stop/Reset Followed by the power button and then wait for it to restart.

====================================================================================